Harman's Machine Shop Inc

Lolo Burks

★★★★★

a year ago

Awesome! Does excellent work, very professional!!

J. Gordon

★★★★★

10 months ago

Good service and very knowledgeable!

Griffin Woodward

★★★★★

2 years ago

Highly recommend. Great work and less than quoted.

Julie Reed

★★★★★

8 years ago

They redid the the heads on truck and did a great job. I highly recommend this ship over any.

Donald Thompson

★★★★★

8 years ago

They were able to get me a seal saver no one could get not even internet, saved me a crank kit

Grant Novak

★★☆☆☆

3 years ago

Told me head was milled 9 thousandths and pressure tested and a week later the head went and doesn't hold pressure in 3 cylinders on the head and looks like it was never touched

Jason Witt

★★★★★

4 years ago

Good people, always willing to help if they can. Not out looking to make a bunch of money. Just making a living and doing a good job at it!

Elizabeth Thurman

★★★★★

5 years ago

Very nice people ! Helpful in every way we have been getting our motor work done by them many years !

Shane Underwood

★★★★★

4 years ago

Had some valves replaced and a new piston prodded on the rod, and they went ahead and did the piston rings for me while they was there, very happy with the service and people!

Steven Epps

★★★★★

2 years ago

Super helpful. Super reasonable. Super old school. Can't machine a rocket fuselage but can do basic stuff well. Which is what they shoot for.

Lj Wickline

★★★★★

4 years ago

Very nice people had them press a hub bearing for me it was done at the time they said it would be and the price was more then reasonable thank you guys im looking forward to doing more business with you

Sean Kelley

★★★★★

9 years ago

I have taken my 05 Subaru legacy gt heads and block to them with fantastic results. I purchased a 93 ish chevrolet small block (bare) and had them machine the crank after I screwed up and let it freeze (marine) and currently they have honed an 05 subaru block and are working the heads and balancing the rods. Always had great results and as an ASE master tech I strongly recommend them as opposed to the folks in the starkey area that ripped me off the last 2 times I went there. Thanks Merrill and Jerry!

Ian A

★☆☆☆☆

11 years ago

Took my head for a valve job/resurface and every valve leaked afterwards. Valves were not bent and at that point head could've been compromised due to the tight tolerances that must be followed. Shop gave me my money back but refused to help with a new head/head gasket.

M T

★★★★★

Edited a year ago

Badass work they did for me had some 3.1 heads and some 2.9 heads and block and other parts they knew what to look for and how to fix the problems with my parts. In doing so they saved me money and time I'd tell you there's none better than Harmon's machine shop. Rip Merrell you were the best of the machinists Harmons machine was legendary and I hold your guys in the highest regards.

Mark Morrison

★★★★★

2 years ago

True old school machinist work there! They will perform a true three angle valve job on my Porsche Cylinder head & skim cut the head gasket surface! I drive an hour each way to get quality work!

George Flynn

★★☆☆☆

11 months ago

Ok, I'll start with they don't answer the phone and have no answering machine so with that I drove 40 miles to speak to them and was informed they don't do engine rebuilds any longer, it would great if they would change their ads. I was annoyed do the price of fuel but nothing I can do except warn other Folks. He did say they still do heads.

Travis Frith

★★★★★

8 months ago

Were do I begin, I called them on a Thursday in need of getting my cylinder heads pressure tested and resurfaced for my 3 valve mustang. Jerry said he could get to them early this week. I called just to check on them today and he said he was finishing the paperwork up and that they were ready to go!!! Incredible turn around time, the quality of the work looks awesome! They also were extremely fair with their pricing. Little shops like this are hard to find that do great quality work like them! I will for sure use them again in the future! Thanks again Jerry! 5 stars!